Making an Inspection Port

After spending much time and effort to properly create the large fuselage skins for my Bede BD-4C airplane, you would think that I would want to keep them nice and whole. You would think wrong. Two of them needed large holes cut into them. The top skin needed a hole for the vertical stabilizer’s spar and the left skin needed an inspection port.

For the inspection port, I set my circular hole cutter as large as it would go (about 4½ inches in diameter), chucked it into my hand drill, and set to drillin’ on my airplane. That was kind of touch and go for awhile. The hole cutter is designed to be used in a drill press, slowly cutting into something which is clamped down and held perfectly perpendicular to the drill bit. You are not supposed to use the circular hole cutter in a hand drill. Fortunately, I do not follow directions well so I used the hand drill anyway. I did concede to setting the drill on low speed using the variable-speed trigger to turn the cutter at just a few RPM. It worked. I got a nice large hole in the fuselage skin.

Hole cut in fuselage skin

Hole cut in fuselage skin

I then cut a slightly over-size piece of aluminum, 6×6 inches, to make the backing ring. I set the circular hole cutter slightly smaller, about 4 inches in diameter, and cut a hole in the backing ring. Then I used my sander to reshape the backing ring from square to round.

The last step was to cut a circle of aluminum to exactly fit in the hole in the fuselage skin, i.e. to be the cover for the inspection port. I roughed it out round and then sanded it down bit by bit until it fit just right. Here are the pieces.

Backing ring and inspection port cover

Backing ring and inspection port cover

The backing ring will get riveted behind the Bede BD-4C skin. Here it is, clecoed in place. The small holes in the ring, visible just inside the clecoes, will be replaced with nutplates.

Inspection port with backing ring

Inspection port with backing ring

The cover goes into the inspection port and fastens to the backing ring. Once complete, there will be screws through the cover, going into the nutplates in the backing ring. I will dimple the metal so that the screw tops are flush with the surface. For this photo, you guessed it, more clecoes.

Inspection port with cover installed

Inspection port with cover installed

Finally, here is the obligatory long shot, so you can see where this inspection port is on the Bede BD-4C airplane.

Inspection port in Bede BD-4C fuselage

Inspection port in Bede BD-4C fuselage

Update 4/10/14 7:40am:

Brian wondered what can be seen through the inspection port. You can see the rudder bellcrank and connections. Here is a photo.

view through inspection port

Rudder controls bellcrank and cable connections, seen through inspection port in the side of a Bede BD-4C

Posted in Bede BD-4C
7 comments on “Making an Inspection Port
  1. Brian says:

    I understand the concept of an inspection port, but what will there be in that section to inspect?

  2. Arturo says:

    Were do you find good little people to get in there and fix things…
    I feel your pain, making a hole on a beautiful sheet of aluminum.

  3. Pete says:

    Hi, Art. It’s too late now for your application but this is the way I overcome issues with using a hole saw in a hand held drill. Prick punch the exact center. Drill pilot with a much smaller bit than the usual 1/4″ mandrel bit. Enlarge the hole in a couple steps to 1/4″. Chuck the hole saw in a drill press to determine if it has any wobble. If it does get another hole saw. If it doesn’t drill a sample hole in scrap stock to determine if it is dimensionally accurate. If not use a file on the exterior kerf until it is on spec. As an aside I always make my own mandrel bits by grinding a flat in an appropriate place on a 1/4″ bit from the drawer. Cheaper and easily customizable.

  4. Brian Ingraham says:

    Hi, Art…

    The sheet metal of the cover is a bit too thin to countersink. Dimpling is the way to recess the screw heads.

    Brian

  5. Mike Lamb says:

    Hi Art, good job. Glad to see you don’t take risks or follow the norm, so to speak. That was quite creative. But how do you get both hands in there to work on these bolts. Have you read the book “the Virginian Patriot”. It was written by Don Hewes and has lots of great ideas for the BD-4. Many of which I am incorporating into my BD-4. Here is the link to find it. It is a good read.
    Mike
    old.bd-4.org/virgian_patriot.html

Categories

Archives